It's no secret that Ray Barton...
It's no secret that Ray Barton Racing Engines has been building, dynoing, and shipping the latest version of the MP 528 Hemi crate engines. Before being crated, Barton dyno-tests all the engines using the same dyno distributor and ignition (MSD Pro Billet, Moroso Blue Max wires, MSD 7AL ignition box and MSD Pro Power coil). In this ignition shootout, Performance Distributors' (PD) new Hemi DUI distributor will have to prove itself without the help of the big MSD 7AL ignition box.
We were jolted to hear Performance Distributors has developed a Hemi D.U.I. distributor that clears the fat Hemi valve covers. One drawback-limited applications due to hood clearance. For Performance Distributors to offer a Hemi D.U.I. they needed to lengthen it 11/2-inches more than the 440 D.U.I. causing hood clearance issues. The benefits of the fatter/wider distributor are reduced spark scatter between the terminals, which leads to a smoother running engine. Inside the distributor is the Dyna-Module that adds dwell time for longer spark duration to ignite the combustion more completely. The coil, also inside the distributor cap, is a high voltage (50,000 volts) unit. All it takes is one 12-volt wire to power the D.U.I. ignition.
Baseline testing with the...
Baseline testing with the MSD ignition showed the Hemi was increasing power output on each pull. We installed the taller and wider D.U.I. distributor with only the 16-volt dyno wire to run the Hemi D.U.I. The stand-alone D.U.I backed up the MSD's numbers and power still increased on each pull as the Hemi continued breaking-in. The D.U.I. did well against a team of racing ignition components.
Fortunately, we were able to test the new Hemi D.U.I. using a brand-new Mopar Performance 528 Hemi crate engine at Ray Barton Racing Engines (all MP 528 Hemis are now built at Ray Barton Racing Engines). Before any MP Hemis are crated and shipped, they're dyno tested on Barton's DTS engine dyno for quality control. The 528 Hemi used for our ignition test was only the 17th Hemi crate engine that Barton's had built at that point. By the time you read this, RBRE will have built, dyno-tested, and shipped over a hundred MP 528 Hemis. Call any MP dealer to order your Hemi, not RBRE. Questions can be directed to the MP tech line: 888-528-HEMI.
Here Dave Barton sets the...
Here Dave Barton sets the D.U.I's timing at the same 30-degrees for a fair comparison. When you consider the mild build-nature of the Crate Hemi (.540-inch lift cam, 10.5:1 compression, un-ported heads/intake, and an 830cfm Holley HP with no special tuning), these Hemi's produce amazing power (over 650).
 Hood clearance for the Hemi...  Hood clearance for the Hemi D.U.I. was checked using our '67 Coronet, equipped with an RB Wedge. The hood closed, but as you can see, the pink play-dough shows how the top edge of the coil cover was up against the hood. On our '67, the hood bracing didn't come close to the distributor. We tried the Hemi DUI using a friend's 440-powered '64 Fury, and we couldn't close the hood. The hood bracing was in the way. |  The coil cover on the left...  The coil cover on the left will become standard issue for the Hemi D.U.I. to aid in needed hood clearance. The cover on the right is featured on all the other D.U.I. distributors. The new cover will add nearly an inch of needed hood clearance for the tall distributor. |  We checked hood clearance...  We checked hood clearance with the stock-type H.E.I. coil/cap cover and gained the needed clearance (see the pink play dough). The Hemi D.U.I. may have fit under the hood of our 67 R/T, but don't expect it to fit under any Shaker, Air Grabber, or Ramcharger equipped hoods. |