There are certain items that we use every time we drive our vehicles, and often these parts are simply taken for granted instead of appreciated. A vehicle's steering wheel is one of those pieces, and so long as the one in your car operates correctly, it probably goes unnoticed. The steering wheel is more important than you think, however, as it is the direct link between the driver and the vehicle's steering system. Optimum driver control greatly depends on not only placement, but the design of the steering wheel as well as the materials the wheel is made of. Further, most modern vehicles have control switches for the radio, cruise control, the navigation system, and more located on the steering wheel, enhancing driver convenience. The most important safety factor of a late-model Mopar's steering wheel is undoubtedly the airbag, which may also scare some enthusiasts away from tackling a job like changing the steering wheel themselves. Fortunately, Grant is offering a new line of airbag steering wheels that are a definite improvement over the factory wheel, and are easy to install as well.
We've been enjoying our '09 Dodge Challenger R/T for some time now, and while we've modified our vehicle's exterior, engine, suspension, and drivetrain, the car's interior has remained relatively untouched. Chrysler did a great job of designing the interiors of their new LX and LY line of vehicles, which are very comfortable and user-friendly. Additionally, the seats in our R/T model offer nearly infinite adjustability as well as side-bolstering for support while cornering and driving aggressively. And while we have upgraded our older Mopars with more modern parts like seats, harnesses, and steering wheels, we didn't consider upgrading the steering wheel for our late-model Dodge until we saw Grant's new "Revolution" product line at a recent trade show.
Knowing what a pain it is to even change the turn-signal switch in a classic Mopar's steering column, we initially made the incorrect assumption that swapping the steering wheel in a late-model car would be even more difficult. Knowing most owners would share our same fear, Grant went to great lengths designing this line of modern steering wheels to not only be ergonomically superior to the factory wheel, but to be easy to install as well. After reading their instructions we were convinced we could accomplish the task without blowing the airbag and causing injury, so we ordered their black steering wheel with gray leather inserts to match the gray inserts of our factory black leather seats.
Through experience we've learned that it's often better to read the instructions before diving into a job like this, so we opened our package from Grant and admired the new steering wheel, while educating ourselves with the included literature. The Grant instructions are clear and concise, and begin with the step of disconnecting the battery of the vehicle for a minimum of five minutes prior to beginning the swap to prevent accidental airbag deployment. During deployment, the airbag is filled rapidly with a very high pressure gas, usually from a small cylinder inside the airbag unit (or under the dash on older vehicles). To allow the gas to pass rapidly into the bag, the cylinder is opened by a pyrotechnic squib, which uses stored battery energy for ignition. By removing the negative battery cable the batteries circuit is broken, and the airbag squibs slowly lose their stored energy.
By design, the airbag shouldn't deploy simply by removing and reinstalling it, even if the battery remains connected. Because airbags are expensive and dangerous, however, we followed the instructions precisely, waiting 30 minutes or so after disconnecting the car's battery before starting the procedure to swap the wheel. As we proceeded, we were surprised at how easy it was to remove the airbag from the steering wheel after simply disconnecting the electrical terminals. Removing the factory steering wheel was simple as well, once the extremely tight retaining bolt was loosened. The LX and LY Mopars don't require any type of special tool to pull the steering wheel like older models, and the electronics simply unplug from a main harness and are left on the wheel.

1a We thought the stock steering...

1a We thought the stock steering wheel in our ’09 Challenger R/T was nice..

1b ...Until we got a look...

1b ...Until we got a look at the new late-model offerings from Grant.

2 After leaving the battery...

2 After leaving the battery unhooked for almost 20 minutes, we could get started. Removing the airbag is the first step to removing the factory steering wheel and should be performed while wearing safety glasses, just in case. By removing the two fasteners with a 10mm socket, the airbag can be detached from the stock steering wheel. Be sure the steering wheel is centered so the new wheel can be clocked the same.
Since the Grant steering wheel utilizes the controls from the factory steering wheel, they must be removed and installed onto the Grant wheel. Making this process easier is the fact that the new wheel already has the provisions for these controls, making the swap simple and fairly self-explanatory. Once swapped, the new wheel is installed in the reverse order, and the electrical components are reconnected before reinstalling the factory airbag. All told we spent a couple of hours changing our steering wheel, including the half hour we waited after disconnecting the battery. Aside from a breaker bar and 10mm Allen-socket to break the retaining bolt loose and torque wrench to tighten it, you just need basic hand tools to accomplish the swap.
Driving our Challenger with the Grant Revolution steering wheel, we noticed the padded leather grips immediately. Not quite at "ten and two" like your driver's education instructor would have liked, these pads are more at 9:30 and 2:30, which we actually prefer. The new steering wheel is comfortable in all driving phases, and though dimensional differences from the stock wheel are subtle, the overall feel of the steering wheel is noticeably improved. Our radio, cruise, and other steering controls are all easy to operate, and the padded area at the wheel's six-o'clock location is a nice alternative when relaxing on the highway.
The steering wheel is aesthetically appealing as well, especially with colors available to match most interior combinations. The gray leather inserts in our steering wheel are a dead-on match to the gray leather inserts in our car's stock seats, resulting in a custom but factory appearing installation. Best of all, this is an improvement any Charger, Challenger, Magnum, or 300 owner can perform in their own driveway in an hour or so, with the nearly immediate gratification of being able to see and feel the improvement in your vehicle.

3 The airbag can now be pulled...

3 The airbag can now be pulled away from the wheel far enough to disconnect the two squib connectors and the horn terminal. The squib connectors squeeze together and pull straight out.

4 Grant recommends, and we...

4 Grant recommends, and we agree, that the airbag should be placed face up in a safe location, like a workbench or the floorboard or passenger seat of the car. It is extremely unlikely that the airbag will deploy, but you don’t want to take chances as accidental deployment can cause damage or injury.

5 With the airbag out of...

5 With the airbag out of the way, the electrical connectors for the cruise control and steering mounted switches can be disconnected.

7 Unlike older vehicles,...

7 Unlike older vehicles, a steering wheel puller isn’t necessary; simply pull down and back from the top, and the wheel comes right off. The wiring harness is fed through the provision in the wheel and will be fed back into the new wheel the same way.

6 The retaining bolt is actually...

6 The retaining bolt is actually a 10mm Allen head, requiring a heavy-duty impact or breaker bar to remove. Once broken loose, this fastener is easily removed and retained for use with the new wheel.

8 If equipped, the cruise...

8 If equipped, the cruise control wiring and controller can be removed and installed on the new steering wheel. We found it easiest to use a small screwdriver to remove the switches for the radio and onboard diagnostics.

8b ...We found it easiest...

8b ...We found it easiest to use a small screwdriver to remove the switches for the radio and onboard diagnostics.

9a The switches and trim...

9a The switches and trim are simply held in place by clips and can be pried out while pinching the clips and pulling upward...

9b ...The wiring is then...

9b ...The wiring is then exposed and can be transferred to the Grant wheel with the other components.

10 It only takes a few minutes...

10 It only takes a few minutes to swap all of the wiring, switches, and trim to the new steering wheel, as most components just snap in place. This steering wheel looks sportier than the factory unit and should improve our car’s interior.

11 The Grant wheel has the...

11The Grant wheel has the same provision for wiring, which can be fed through the hole as the steering wheel is installed. The wiring can all be connected now with the exception of the airbag and horn wires which will be the final step.

12 The center retaining bolt...

12 The center retaining bolt is tightened to a torque of 52 lb-ft using a torque wrench. This is the only part of the installation that requires anything but standard (ok, metric) hand tools.

13 Wearing safety glasses,...

13 Wearing safety glasses, the airbag’s electrical terminals can be reconnected before the airbag is installed in the new steering wheel. We must admit this installation was easier than we first anticipated and can be accomplished by even a novice mechanic with the proper tools in a couple of hours.

14 We like the look and feel...

14 We like the look and feel of the new Grant steering wheel, and the gray leather inserts of the wheel are a perfect match to our black and gray leather seats. Check out Grant’s website to see all of the color combinations available for late-model Mopars.

15 Our driving impressions...

15 Our driving impressions of the Grant Revolution steering wheel were very favorable. The wheel is comfortable in the hands, and switches and controls are easy to use. We liked the positioning of the leather inserts, finding the new steering wheel aesthetically appealing as well as fun to drive with.